FX Wash
FX Australia® Product Information
(Interior & Exterior)
Product Description
FX Wash is a unique, acrylic-based coating using modern technology to create an aged, translucent finish. It adds
charm and character to FX Australia textured coatings, such as FX Stone and FX Mud Paint™ and brings a lucent quality
to non-textured coatings like FX Lemon Tree Creek® Low Sheen and FX Lemon Tree Creek® Semi-Gloss.
FX Wash is a simple, one-coat product that dries flat. Further coats may be applied to achieve different effects.
Ease of application
Attractive finish
Easy spreading
Smooth finish
Easy clean-up
FX Wash produces many different special effects on interior surfaces such as plaster, plasterboard, and on bagged and
rendered walls.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust, grease, loose or flaking paint, and loose surface plaster.
Efflorescence or mould on masonry or concrete surfaces must be treated. Flatten gloss surfaces by thoroughly sanding
and wipe clean with a damp cloth. Then apply FX Lemon Tree Creek® Undercoat as required. If using over
FX Mud Paint™, or other FX Australia textured coating, for best results FX Australia suggests applying two coats of the
selected textured coating, white or tinted, followed by one coat of tinted FX Wash. FX Wash can also be applied over
FX Lemon Tree Creek® Low Sheen or FX Lemon Tree Creek® Semi-Gloss, white or tinted.
Stir contents thoroughly before use with a broad, flat stirrer, using an upward action.
Brush/Roller: Use a 75 mm or 100 mm brush or a short or long nap roller, depending on required finish. If using a brush,
apply FX Wash freely, overlapping as you go, to achieve a more stylish finish. Can also be applied with a mitt or sponge
to produce other special effects.
For more durability, on internal surfaces only, we suggest finishing with a top coat of FX Super Matt Clear.
Approximate Spreading Rate: 16 square metres per litre, depending on application technique and surface
Approximate Film Thickness per coat: Wet: 45 Microns; Dry: 20 Microns.
Requires: One coat for a simple translucent finish. Further coats achieve different effects.
Thinner: N/A
Tinting: Refer to colour chart for tinting specifications.
Method: Brush, roller, mitt or sponge.
Drying Times (at 25
C): Touch: 2 Hours; Recoat: Not required.
Note: Do not apply paint if the air temperature or substrate temperature is below 10 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask. Gloss Level: Less than 5% at a 60° viewing angle.
Safety and Environmental Care
Personal Protection: Wear eye protection and dust mask when spraying, as splashes may cause eye irritation and inhalation of spray
mist may cause respiratory irritation.
Asbestos cement sheeting: Do not disturb, sand or scrub, and avoid any peripheral dust. If you do not have professional expertise
in the handling/removal of asbestos sheeting, use a licensed asbestos removalist.
Refer to product labels, current FX Australia Safety Data Sheets or call FX Australia for detailed information.
Slippery when spilled • Restrict access to area until clean-up is completed
When cleaning up spills, use personal protection
Stop leak if safe to do so and contain spill with absorbent material such as sand, vermiculite or other inert material
Prevent spill from entering waterways • Collect and dispose of spilled material according to local regulations
Wash away remnants
with liberal amounts of cold water.
Store in a cool, dry, well-ventilated place out of direct sunlight
Store away from strong acids and moisture
Keep containers
closed at all times and check regularly for spills.
Refer to State/Territory Land Waste Management Authority: most authorities permit disposal at approved land waste sites.
Date of Issue: March 2014
FX Australia Pty Ltd | ABN: 75 089 071 385 | 86 Redfern Street, Wetherill Park NSW 2164 Australia
T +61 2 9725 5888 | F +61 2 9757 2688 | E sanvito@fxaustralia.com.au | W www.fxaustralia.com.au