FX Australia® Product Information
Product Description
FX MAX Easy Clean
(Interior only)
FX MAX Easy Clean is a high-performance, 100% acrylic, low sheen coating for interior walls. It is ultra stain-resistant,
washable, and specifically formulated to withstand family wear and tear in high traffic areas and to minimise the time
and work required to achieve a maximum, luxury finish in busy living spaces.
Features
Benefits
Water-based
Ease of application
Washable
Easy spreading
Tintable
Easy clean-up
Uses
FX MAX Easy Clean is ideal for interior surfaces such as plaster, plasterboard, iron, cement render and timber.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust, grease, loose or flaking paint, and loose surface plaster.
Efflorescence or mould on masonry or concrete surfaces must be treated. Flatten gloss surfaces by thoroughly sanding
and wipe clean with a damp cloth. Then apply FX MAX Superprep as required, one coat minimum.
Application
Stir contents thoroughly before and during use with a broad, flat stirrer, using an upward action.
Brush/Roller: Apply product using a 75 mm–100 mm brush, or medium or long nap roller.
Airless/Conventional spray: Suitable for application using all standard equipment. Up to 10% water per litre may be
added to aid atomisation.
Approximate Spreading Rate: 14–16 square metres per litre, depending on application technique and surface
roughness.
Approximate Film Thickness per coat: Wet: 90 Microns; Dry: 25 Microns.
Requires: 2 coats.
Thinner: Water, 10% if required.
Tinting: Refer to colour chart for tinting specifications.
Method: Brush, roller or airless/conventional spray equipment.
Drying Times (at 25 °C): Touch: 40 Minutes; Recoat: 4 Hours.
Note: Do not apply paint if the air temperature or substrate temperature is below 10 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask. Gloss Level: 5%–10% at a 60° viewing angle.
Safety and Environmental Care
Safety
Personal Protection: Wear eye protection and dust mask when spraying, as splashes may cause eye irritation and inhalation of spray
mist may cause respiratory irritation.
Asbestos cement sheeting: Do not disturb, sand or scrub, and avoid any peripheral dust. If you do not have professional expertise in the
handling/removal of asbestos sheeting, use a licensed removalist.
Refer to product labels, current FX Australia Safety Data Sheets or call FX Australia for detailed information.
Clean-up
Slippery when spilled· Restrict access to area until clean-up is completed · When cleaning up spills, use personal protection
equipment · Stop leak if safe to do so and contain spill with absorbent material such as sand, vermiculite or other inert material ·
FX Australia Pty Ltd | ABN: 75 089 071 385 | 86 Redfern Street, Wetherill Park NSW 2164 Australia
T +61 2 9725 5888 | F +61 2 9757 2688 | E sanvito@fxaustralia.com.au | W www.fxaustralia.com.au
Prevent spill from entering waterways · Collect and dispose of spilled material according to local regulations · Wash away remnants
with liberal amounts of cold water.
Storage
Store in a cool, dry, well-ventilated place out of direct sunlight · Store away from strong acids and moisture · Keep containers closed
at all times and check regularly for spills.
Disposal
Refer to State/Territory Land Waste Management Authority: most authorities permit disposal at approved land waste sites.
Date of Issue: March 2014
FX Australia Pty Ltd | ABN: 75 089 071 385 | 86 Redfern Street, Wetherill Park NSW 2164 Australia
T +61 2 9725 5888 | F +61 2 9757 2688 | E sanvito@fxaustralia.com.au | W www.fxaustralia.com.au