FX Australia® Product Information
FX Easy Sanding Stucco(Interior only)
An experienced applicator is highly recommended for this product.
Product Description
FX Easy Sanding Stucco is a superior, acrylic plaster finish. Its depth and movement mimic the classical ‘Grasello Di
Calce’ or Venetian plaster to give a subtle, undulated colour effect. The coating dries to a matt finish and can be
trowel-polished to a satin finish or sandpapered to a high sheen, creating a perfect backdrop for both classic and
contemporary art and accents.
Features Benefits
Ease of application
Attractive finishes
Easy spreading
Many varying effects
Easy clean-up
FX Easy Sanding Stucco can be used on most interior surfaces such as plaster, plasterboard and cement render or
sound, previously painted surfaces.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust, grease, loose or flaking paint, and loose surface plaster.
Efflorescence or mould on masonry or concrete surfaces must be treated. Flatten gloss surfaces by thoroughly sanding
and wipe clean with a damp cloth. Then apply FX Stucco Undercoat as required. For best results, surfaces should be
well prepared and smooth.
Stir contents thoroughly before and during use with a broad, flat stirrer using an upward action, or ideally use
a power-driven mixing paddle.
Trowel: Requires 2–3 coats applied with a stainless steel stucco trowel. Different sized trowels give different finishes. Place
a small amount of product onto the trowel and apply evenly over prepared surface. Trowel is held at an approximate
45-degree angle to the surface during application. To correct imperfections in each coat before applying next coat,
use 220-grade sandpaper or higher. When final coat is slightly dry, polish with a stainless steel stucco trowel to achieve
desired special effect. This coating can also be polished with a special sandpaper to achieve a high sheen when
completely dry. FX Australia suggests using a worn, ultra-fine sanding block.
Clear Coating: Generally not required. For hardwearing areas or to achieve water resistance, apply a coating of clear
FX Wicked Wax® by trowel.
Approximate Spreading Rate: 4–6 square metres per litre, depending on application technique and surface roughness.
Approximate Film Thickness per coat: Wet: 400 Microns; Dry: 250 Microns.
Requires: 2–3 coats.
Thinner: Not required.
Tinting: Refer to colour chart for tinting specifications.
Method: Stainless steel stucco trowel.
Drying Times (at 25 °C): Touch: 2 Hours; Recoat: 6 Hours.
Note: Do not apply paint if the air temperature or substrate temperature is below 10 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask. Gloss Level: 20%–30% at a 60° viewing angle after final coat is polished.
Safety and Environmental Care
Personal Protection: Wear eye protection and dust mask when spraying, as splashes may cause eye irritation and inhalation of spray
mist may cause respiratory irritation.
Asbestos cement sheeting: Do not disturb, sand or scrub, and avoid any peripheral dust. If you do not have professional expertise in the
handling/removal of asbestos sheeting, use a licensed asbestos removalist.
Refer to product labels, current FX Australia Safety Data Sheets or call FX Australia for detailed information.
Slippery when spilled · Restrict access to area until clean-up is completed · When cleaning up spills, use personal protection
equipment · Stop leak if safe to do so and contain spill with absorbent material such as sand, vermiculite or other inert material ·
Prevent spill from entering waterways · Collect and dispose of spilled material according to local regulations · Wash away remnants
with liberal amounts of cold water.
FX Australia Pty Ltd | ABN: 75 089 071 385 | 86 Redfern Street, Wetherill Park NSW 2164 Australia
T +61 2 9725 5888 | F +61 2 9757 2688 | E sanvito@fxaustralia.com.au | W www.fxaustralia.com.au