FX Australia® Product Information
FX Exterior Copper(Interior & Exterior)
Product Description
FX Exterior Copper finish is a water-based, liquid paste, specifically formulated to imitate the lustre and highly decorative
colours of copper. Because it’s tintable, it’s possible to produce many patinas and tones from the rich copper base, and
by using a sponge, brush roller or spray, to create unusual patterns and special effects. This hard-wearing coating
is a no-fuss replacement for copper sheeting and provides a simple solution wherever the decorative charm of copper
is required.
Features Benefits
Water-based
Ease of application
Attractive finish
Easy sanding
Washable
Easy clean-up
Tintable
Range of colours
Uses
FX Exterior Copper is used for producing many different special effects. Suitable for all surfaces such as plaster, plasterboard, iron,
cement, trim, doors, furniture and timber.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust, grease, loose or flaking paint, and loose surface plaster. Efflorescence
or mould on masonry or concrete surfaces must be treated. Flatten gloss surfaces by thoroughly sanding and wipe clean with a damp
cloth. Then apply FX Lemon Tree Creek® Sealer Undercoat as required. If you have tinted the FX Exterior Copper coating,
tint the FX Lemon Tree Creek® Sealer Undercoat to match as closely as possible.
For best results, surfaces should be well prepared and smooth.
Application
Stir contents thoroughly before and during use with a broad, flat stirrer using an upward action.
Brush/Roller: Apply the first coat by roller. Ensure the roller is very soft and between 12 mm–18 mm. The second coat may be applied
by roller or with a 100 mm brush, using a criss-cross motion. Use the same method to apply subsequent coats if necessary.
Note: When rolling, use a short or medium nap roller. Back-roll to avoid inconsistent reflections.
Sponge (interior application): Prepare surface as above. Then apply 1–2 coats of FX Lemon Tree Creek® Semi-Gloss in a strong colour,
such as red or black. Using a sea sponge, dab FX Exterior Copper from a small amount in paint tray lightly onto paper, then lightly onto
prepared surface. Continue until surface area is covered, ensuring that base colour remains visible behind the sponge effect.
For advice on sponging or other techniques, contact FX Australia.
It is important to keep a wet edge at all times. To slow down the drying time (interior applications only), add approximately
10% of FX Scumble.
Conventional Spray: Suitable for application using all standard spray equipment. Best results are achieved on smooth surfaces.
Approximate Spreading Rate: 9–10 square metres per litre, depending on application technique and surface roughness.
Approximate Film Thickness per coat: Wet: 70 Microns; Dry: 25 Microns.
Requires: 2–3 coats.
Thinner: Water.
Tinting: Refer to colour chart for tinting specifications.
Method: Brush, conventional or special rollers, sponge or conventional spray equipment.
Drying Times (at 25 °C): Touch: 2 Hours; Recoat: 6 Hours.
Note: Do not apply paint if the air temperature or substrate temperature is below 10 °C or above 35 °C. The temperature should not fall
below 10 °C during the drying process.
Clean up: Water. Safety: Dust Mask. Gloss Level: 20%–30% at a 60° viewing angle.
Safety and Environmental Care
Safety
Personal Protection: Wear eye protection and dust mask when spraying, as splashes may cause eye irritation and inhalation of spray
mist may cause respiratory irritation.
Asbestos cement sheeting: Do not disturb, sand or scrub, and avoid any peripheral dust. If you do not have professional expertise in the
handling/removal of asbestos sheeting, use a licensed asbestos removalist.
Refer to product labels, current FX Australia Safety Data Sheets or call FX Australia for detailed information.
Clean-up
Slippery when spilled· Restrict access to area until clean-up is completed · When cleaning up spills, use personal protection
equipment · Stop leak if safe to do so and contain spill with absorbent material such as sand, vermiculite or other inert material ·
Prevent spill from entering waterways · Collect and dispose of spilled material according to local regulations · Wash away remnants
with liberal amounts of cold water.
Storage
FX Australia Pty Ltd | ABN: 75 089 071 385 | 86 Redfern Street, Wetherill Park NSW 2164 Australia
T +61 2 9725 5888 | F +61 2 9757 2688 | E sanvito@fxaustralia.com.au | W www.fxaustralia.com.au